壓力設備ce認證（ped指令）核心要求：
1.高于特定壓力/容積門檻的壓力設備和組件必須要：
具備安全性
符合設計、制造、和測試的基本安全要求
滿足適當?shù)姆闲栽u定程序
2.低于特定壓力/容積門檻的壓力設備和組件必須要：
具備安全性
依據完善的工程實務而設計、制造
產品歸類與符合性評定模式的選擇
壓力設備ce認證（ped指令）范圍
歐盟委員會企業總司界定的關于壓力裝置指令pressure equipment 97/23/ec適用范圍廣泛，主要包括下列壓力裝置和領域：
壓力設備ce認證標準
| standard/標準 | deion /描述 |
| en 378-1:2008 | refrigerating systems and heat pumps - safety and environmental requirements - part 1: basic requirements. definitions. classification and selection criteria制冷系統和加熱泵規范.安全性和環境要求:.基本要求、定義、分類和選擇規范。 |
| en 3782 :2008 | aerospace series - holes for 100° countersunk head screws - design standard制冷系統和加熱泵規范.安全性和環境要求:.設計、建造、檢驗、標志及文件。 |
| en 378-3 :2000 | refrigerating systems and heat pumps - safety and environmental requirements - part 3: installation site and personal protection-includes amendment a1:2003制冷系統和加熱泵規范.安全性和環境要求:.安裝地點和人員保護。 |
| en 378-4 :2008 | refrigerating systems and heat pumps - safety and environmental requirements - part 4: operation. maintenance. repair and recovery制冷系統和加熱泵規范.安全性和環境要求:.運行、維護修理和恢復。 |
| en 473 :2008 | non-destructive testing - qualification and certification of ndt personnel - general principles無損檢驗 — 無損檢驗人員的資格和證書 — 一般原則 |
| en 583-1 :1998 | non-destructive testing ultrasonic examination part 1: general principles-includes amendment a1:2003無損檢驗.超聲波檢驗.一般規則 |
| en 583-5 :2000 | non-destructive testing - ultrasonic examination - part 5: characterization and sizing of discontinuities-includes amendment a1:2003損檢驗.超聲波檢驗.不連續性檢驗的特征和尺寸測量 |
| en 1252-1 :1998 | cryogenic vessels materials part 1: toughness requirements for temperatures below p80 °c-incorporating corrigendum december 1998低溫容器.材料.溫度低于-80℃時的韌度要求 |
| en 1252-2 :2001 | cryogenic vessels - materials - part 2: toughness requirements for temperatures between -80 degrees c and -20 degrees c低溫容器.材料.溫度在-80--20度的韌度要求 |
| en 1289 :1998 | non-destructive testing of welds penetrant testing of welds acceptance levels-includes amendments a1: 2002 and a2:2003焊接的無損檢驗.焊接的超聲波探檢驗.驗收等級 |
| en 1291 :1998 | non-destructive testing of welds magnetic particle testing of welds acceptance levels-includes amendments a1:2002 and a2:2003焊縫的無損檢驗.焊縫的磁粉檢驗.驗收等級 |
| en 1349 :2000 | industrial process control valves-incorporating corrigendum october 2001工業工藝控制閥 |
符合性評定(conformity assessment)程序適用于第i~iv類的設備，廠商的選擇組合如下：
| 第i類 | 第ii類 | 第iii類 | 第iv類 |
| a | a1 | b1+d | b+d |
| d1 | b1+f | b+f | |
| e1 | b+e | g | |
| b+c1 | h1 | ||
| h |
對于只須適用較低要求模式的產品，廠商也可以選擇應用較高要求的模式。
各模式的說明如下：
| 模式 | |
| a | 內部生產管制 |
| a1 | 內部制造檢查加上最終評審監督 |
| b | ec型式檢查 |
| b1 | ec設計檢查 |
| c1 | 符合型式 |
| d | 生產品質保證(iso 9002) |
| d1 | 生產品質保證(iso 9002)( 模式單獨應用) |
| e | 產品品質保證(iso 9003)最終檢驗與測試 |
| e1 | 產品品質保證(iso 9003)( 模式單獨應用) |
| f | 產品檢查 |
| g | ec個別檢查 |
| h | 全面品質保證(iso 9001) |
| h1 | 全面品質保證(iso 9001)加上設計檢查及最終評定的特別監查
|
